网站首页 || 关于我们 || 传媒产品 || 安防产品 || 应用方案 || 资料下载 || 技术文章 || 公司新闻 || 诚聘英才 || 联络我们 || 疑难解答
 

网站位置:安防产品>4进8出有源双绞线视频接收器 (电位器细调型 拨码开关型)

产品型号: UST104R-F2  - 独家单电位器增益均衡同步调节
产品型号: UST104R-2 - 拨码开关单电位器增益均衡同步调节
 
 多路有源传输器产品手册 (中文)
 
 
UST104R-2 UST104R-F2 4进8出有源双绞线视频分配接收器

100-1600米传输距离 低工作电压 4通道1进2出广播级分配输出

(UST104R-2拨码开关型    UST104R-F2单电位器细调型)

双绞线视频传输概述:

传统的同轴电缆和光纤传输方式解决了近距离和远距离的视频传输问题,100-2000米左右的视频图像信号传输成为监控领域的瓶颈。双绞线视频传输设备,使用价格便宜、取材方便的五类或五类以上的非屏蔽双绞线(UTP计算机网线)四对线中的一对线传输一路高质量的视频信号,其余双绞线线对可以用来传输音频信号或控制云台的RS-485数据等,也可以传输更多的视频信号,而且信号之间互不干扰,传输距离0~2000米可选。双绞线视频传输设备具有超强的干扰抑制能力,对于干扰较大的环境,比如在电梯、水泥厂、钢厂、电厂等强电磁干扰环境,都可以很好的使用。使用这种传输方式,具有布线方便、设备安装简单、可靠性高、抗干扰能力强、传输效果好、系统成本低廉等许多优点。双绞线传输设备的使用改变了智能大厦、智能小区以及各种监控场所的传统布线方式,为监控工程系统设计提供一种高性价比的解决方案。

产品介绍:

UST104R-2和UST104R-F2分别为拨码开关型单电位器细调型4进8出有源BALUN (BALance-UNbalance, 平衡-非平衡)双绞线视频分配型接收器,使用五类或五类以上非屏蔽双绞线作为传输介质实时传输单色或彩色PAL NTSC SECAM等制式的基带视频信号,4xUST101T、4xUST102BP或1xUST104RP_UST104SP、或1xUST104TUST104R UST104R-F UST104R-2 UST104R-F2 (4进8出双绞线视频接收器)组合使用来传输4路PAL制视频信号标称传输距离0-1600米(传输NTSC制信号距离可达2000米),可根据传输距离简单设置发送器拨码开关和接收器的拨码开关(UST104R UST104R-2)或电位器(UST104R-F UST104R-F2)的调节使显示效果最佳即可调试简单方便,人性化的产品设计从而避免同类产品因采用2个电位器或1个拨码另加1个电位器调节方式的不确定性而引发的繁琐工作。250MHz广播级视频带宽的4通道1进2出高保真缓冲分配输出可使UST104R-2或UST104R-F2同时连接DVR和大屏监控电视墙。

UST104R-2/UST104R-F2超强的干扰抑制超低的电磁辐射能力可以使电话 RS485控制数据、音频、多路视频甚至低压电源共缆传输。在一根五类以上的非屏蔽双绞线中的四对线任取一对线,就可以传输一路信号,四对线可以传输四路视频或多种信号的组合而且互不干扰,产品内建瞬态冲击保护措施,有很强的环境适应能力。产品采用抗电磁干扰的金属机壳,支持壁挂式安装、面板安装、堆叠安装、工业导轨式安装等多种安装方式。

安装尺寸为:160mm×88mm ×55mm

产品特点:

★ 4路点对点实时视频传输
★ 超强横纹干扰抑制
★ 高质量的视频效果
★ 亚光喷沙抗辐射金属机壳
拨码增益均衡同步调节-UST104R-2
单电位器增益均衡同步调节-UST104R-2F
★ 电源线碰触保护
★ 多级视频+电源防雷设计
★LED视频/电源指示
★视频随信号强弱明显变化
★ 电源极性反接/视频端口错接保护
★7-24V AC/DC 宽电压输入范
★超低工作电压
★ SMT表贴工艺设计
★抗静电、热插拔、自恢复保险、浪涌、过压、过流、短路、限幅等多达十重线路瞬态冲击保护

工程应用图例

English Version

UST104R-2 UST104R-F2 Quad Channel 1to2 Active UTP CAT5 Video Receiver
1000-4000ft  Lightning Surge Protection / Figure Enhanced Model

Introduction
UST104R-2 / UST104R-F2 UTP CAT5 Video Receiver is an active (amplified) device that allows the extension of real-time monochrome or color video on up to 4000ft ,using Category-5 Unshielded Twisted-Pair (UTP) CAT5 networking wire. Baseband (composite, PAL/NTSC/SECAM) signals of any type are supported.

The unparalleled interference rejection and low emissions of the Model UST101T UST104T & UST104R-2 allows long run video signals to co-exist in the same wire bundle as telephone, datacom, or low-voltage power circuits. This allows the use of shared or existing cable plant. Ground-lifting ensures no annoying "hum-bars" when ground potential differences exist. With built-in lightning protection,transient protection, ESD protection,damaging voltage spike problems are eliminated.

Equipment Specifications

Cable DistanceUp to 4000ft, UST101T(or UST104T)+UST104R-2 / UST104R-2F UTP CAT5 or better.

The transmission of real-time PAL, NTSC or SECAM video signals.

Image figure enhanced in output of UST104R-2 / UST104R-F2 Receiver.

Lightning protection, Transient protection, ESD protection, damaging voltage spike problems are eliminated.

Dimensions no excluding BNC: 170mm×90mm×55mm.

Technical Specifications

Video Frequency Response  DC to 6 MHz.

Distance Switch 4-Position Adjustable for each channel.

Common-mode / Differential-mode Rejection 15KHz to 5 MHz 60 dB typ.

Line Impedance

Coax, female BNC 75 ohms.

UTP, Terminal Block 100 ohms.

Wire Type

Network Wiring 2 Unshielded Twisted Pair 24-16 AWG (0.5-1.31mm).

Category Type Cat 5 or better.

Impedance 100 ± 20 ohms.

DC Loop Resistance 52 ohms per 1,000 ft (18 ohms per 100 m).

Differential Capacitance 19 pF/ft max (62 pF/m max).

LED Indicators

Power On  Red Indicator Light.


Power Supply Range

Transmitter/Receiver: 9-12V AC/DC (MAX 24V AC/DC) DC/AV 9-12V 500 mA  MAX (24VAC/DC).

Environmental

Temperature  0°C to +50° C.

Humidity (non-condensing) 0 to 95%.

Transient Immunity

6,000 V 1.2μS x 50 μS per ANSI/IEEE 587 C62.41 B3.
3,000 V 8μS x 20 μS when ground screw terminal is bonded to earth-ground.

Installmen

1:Put the video signals you need in the VIDEO IN of UST101T (or UST104T).
2: Put a twisted-pair in the each channel VIDEO A, B of UST104R-2/ UST104R-F2.

3: Connect with the mains following instructions shown in the sketch map, make sure that the power should be between DC/AC 9 to 24V. Recommend work in DC 12V.
Recommend to share 12V DC power supply with camera in transmitter termination.

4: Set the position of ADJ correctly according to the distance table in UST101T(or UST104T) & UST104R-2/ UST104R-F2 sub-surface.

5: After the four steps, the VIDEO output of UST104R-2/ UST104R-F2 is ready to work..

Check After Connection

1. Power On        Red LED Indicator Light.

2. Make sure that every wire is correctly and firmly connected.

Mechanical

Dimensions no excluding BNC  170mm×90mm ×55mm.

Material Metal

3 Year Warranty

 
 


COPYRIGHT© 意灵思科技 Elinx Technology Co.,Ltd.    mail:elinxsz@126.com unionst@126.com
公司地址:深圳市南山区前海路3101号10栋14楼 Add:14Fl., 10Bld., No. 3101, Qianhai Rd. Nanshan Dis., Shenzhen, China
Tel: +86 755 26442005 26442235 Mobile: +86 13530886175 13715398087 网站信息备案序号: 粤ICP备05047207号